Home > SLINGSHOT TBARS > SLINGSHOT 2015/16 RG > 18 INCH
Sort By:
Page of 1
18 inch SLINGSHOT-TBARS RAW (RG15)

Features of your 18" Westcoast-Slingshots RG15

Fitment:
* 2015-18 ROAD GLIDES
for 2014 and earlier bikes see SLINGSHOTS Category

* 2018 and earlier STREET GLIDES

VERY IMPORTANT: Cable and wiring extensions will be needed for this size.

Coating: RAW METAL

Top Crossbar: -The Center "U's" in the center and rises up 2" and then the 1-1/4" tubing is swaged (tapered) down to 1" diameter. (Fits conventional controls) - Both sides have 1/2" holes punched for internal wiring. - Cross width is 28" across and pullback is 3 1/2". - Your Wrist angle will be at a 18 degree angle. The top cross bar is welded to sit flat on a 28 degree rake. The throttle side tubing at 1" is honed out and notched for fly by wire The (2) - 3/4" holes in middle of the bar are made to be centered for the 3 1/2 spacing of the risers.

Risers: - All cuts and holes are made by Laser cutting - 3 1/2" spacing between risers. (Fits conventional top triple tree clamps) - 5/8" oval internal wiring holes.

Recommendations: - Heavy Duty Bushings - Grade 8 bolts

Keynote: - These Handlebars are measured by overall height 16 inch risers with the 2 inch rise on the top cross bar equals 18 inches. - 4 total weld points.
- 2 holes will need to be made in the nacelle plastic to pass through and bolt down directly to the triple trees.
- On road glides the nipple on the underside of the vibration dampener on the inside part of the controls must be cut off to fit on our bars.
Here is RG15 Nacelle Cutout template link. CLICK HERE TO DOWNLOAD!

Our Price: $250.00
18 inch SLINGSHOT-TBARS POWDERCOAT BLACK (RG15)

Features of your 18" Westcoast-Slingshots RG15

Fitment:
* 2015-18 ROAD GLIDES
for 2014 and earlier bikes see SLINGSHOTS Category

* 2018 and earlier STREET GLIDES

VERY IMPORTANT: Cable and wiring extensions will be needed for this size.

Coating: POWDERCOAT BLACK

Top Crossbar: -The Center "U's" in the center and rises up 2" and then the 1-1/4" tubing is swaged (tapered) down to 1" diameter. (Fits conventional controls) - Both sides have 1/2" holes punched for internal wiring. - Cross width is 28" across and pullback is 3 1/2". - Your Wrist angle will be at a 18 degree angle. The top cross bar is welded to sit flat on a 28 degree rake. The throttle side tubing at 1" is honed out and notched for fly by wire The (2) - 3/4" holes in middle of the bar are made to be centered for the 3 1/2 spacing of the risers.

Risers: - All cuts and holes are made by Laser cutting - 3 1/2" spacing between risers. 5/8" oval internal wiring holes.

Recommendations: - Heavy Duty Bushings - Grade 8 obolts

Keynote: - These Handlebars are measured by overall height 16 inch risers with the 2 inch rise on the top cross bar equals 18 inches. - 4 total weld points.
- 2 holes will need to be made in the nacelle plastic to pass through and bolt down directly to the triple trees.
- On road glides the nipple on the underside of the vibration dampener on the inside part of the controls must be cut off to fit on our bars.

Here is RG15 Nacelle Cutout template link. CLICK HERE TO DOWNLOAD!

Our Price: $295.00
18 inch SLINGSHOT-TBARS CHROME (RG15)

Features of your 18" Westcoast-Slingshots RG15

Fitment:
* 2015-18 ROAD GLIDES
for 2014 and earlier bikes see SLINGSHOTS Category

* 2018 and earlier STREET GLIDES

VERY IMPORTANT: Cable and wiring extensions will be needed for this size.

Coating: CHROME

Top Crossbar: -The Center "U's" in the center and rises up 2" and then the 1-1/4" tubing is swaged (tapered) down to 1" diameter. (Fits conventional controls) - Both sides have 1/2" holes punched for internal wiring. - Cross width is 28" across and pullback is 3 1/2". - Your Wrist angle will be at a 18 degree angle. The top cross bar is welded to sit flat on a 28 degree rake. The throttle side tubing at 1" is honed out and notched for fly by wire The (2) - 3/4" holes in middle of the bar are made to be centered for the 3 1/2 spacing of the risers.

Risers: - All cuts and holes are made by Laser cutting - 3 1/2" spacing between risers. (Fits conventional top triple tree clamps) - 5/8" oval internal wiring holes.

Recommendations: - Heavy Duty Bushings - Grade 8 bolts

Keynote: - These Handlebars are measured by overall height 16 inch risers with the 2 inch rise on the top cross bar equals 18 inches. - 4 total weld points.
- 2 holes will need to be made in the nacelle plastic to pass through and bolt down directly to the triple trees.
- On road glides the nipple on the underside of the vibration dampener on the inside part of the controls must be cut off to fit on our bars.

Here is RG15 Nacelle Cutout template link. CLICK HERE TO DOWNLOAD!

Our Price: $315.00