10 inch MX-TBARS RAW (RG15)

Features of your 10" Westcoast-Mxtbars RG15

Fitment:
* 2015-2020 ROAD GLIDES
for 2014 and earlier bikes see MX-TBARS Category
* 2018 and earlier STREET GLIDES

VERY IMPORTANT: ABS and NON ABS Road glides can use these bars with the current stock cables and wiring.

Coating: RAW

Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up 2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter. (Fits conventional controls)
- Both sides have 1/2" holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for the 3 1/2 spacing of the risers.
The throttle side tubing at 1" is honed out and notched for fly by wire.

Risers: 3 1/2" spacing between risers. (Fits conventional top triple tree clamps). 1/2" x 5/8" oval holes are 1 7/8" up from the bottom for internal wiring.

Recommendations:
- Heavy Duty Bushings FOR ROAD GLIDE
- Grade 8 or Grade 9 (L9) bolts
Keynote:
- These Handlebars are measured by overall height 8 inch risers with the 2 inch rise on the top cross bar equals 10 inches.
- 4 total weld points
-2 holes will need to be made in the nacelle plastic to pass through and bolt down directly to the triple trees.
- On road glides the nipple on the underside of the vibration dampener on the inside part of the controls must be cut off to fit on our bars.

Here is RG15 Nacelle Cutout template link.CLICK HERE TO DOWNLOAD!

12 inch MX-TBARS RAW (RG15)

Features of your 12" Westcoast-Mxtbars RG15

Fitment:
* 2015-2020 ROAD GLIDES
for 2014 and earlier bikes see MX-TBARS Category
* 2018 and earlier STREET GLIDES

VERY IMPORTANT: ABS and NON ABS Road glides can use these bars with the current stock cables and wiring.

Coating: RAW

Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up 2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter. (Fits conventional controls)
- Both sides have 1/2" holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for the 3 1/2 spacing of the risers.
The throttle side tubing at 1" is honed out and notched for fly by wire.

Risers: 3 1/2" spacing between risers. (Fits conventional top triple tree clamps). 1/2" x 5/8" oval holes are 1 7/8" up from the bottom for internal wiring.

Recommendations:
- Heavy Duty Bushings FOR ROAD GLIDE
- Grade 8 or Grade 9 (L9) bolts
Keynote:
- These Handlebars are measured by overall height 10 inch risers with the 2 inch rise on the top cross bar equals 12 inches.
- 4 total weld points
- 2 holes will need to be made in the nacelle plastic to pass through and bolt down directly to the triple trees.
- On road glides the nipple on the underside of the vibration dampener on the inside part of the controls must be cut off to fit on our bars.

Here is RG15 Nacelle Cutout template link.CLICK HERE TO DOWNLOAD!

18 inch MX-TBARS RAW (RG15)

Features of your 18" Westcoast-Mxtbars RG15

Fitment:
* 2015-2020 ROAD GLIDES
for 2014 and earlier bikes see MX-TBARS Category
* 2018 and earlier STREET GLIDES

VERY IMPORTANT: Cable and wiring extensions will be needed for this size.

Coating: RAW

Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up 2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter. (Fits conventional controls)
- Both sides have 1/2" holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for the 3 1/2 spacing of the risers.
The throttle side tubing at 1" is honed out and notched for fly by wire.

Risers: 3 1/2" spacing between risers. (Fits conventional top triple tree clamps). 1/2" x 5/8" oval holes are 1 7/8" up from the bottom for internal wiring.

Recommendations:
- Heavy Duty Bushings FOR ROAD GLIDE
- Grade 8 or Grade 9 (L9) bolts
Keynote:
- These Handlebars are measured by overall height 16 inch risers with the 2 inch rise on the top cross bar equals 18 inches.
- 4 total weld points
- 2 holes will need to be made in the nacelle plastic to pass through and bolt down directly to the triple trees.
- On road glides the nipple on the underside of the vibration dampener on the inside part of the controls must be cut off to fit on our bars.

Here is RG15 Nacelle Cutout template link.CLICK HERE TO DOWNLOAD!

14 inch MX-TBARS RAW (RG15)

Features of your 14" Westcoast-Mxtbars RG15

Fitment:
* 2015-2020 ROAD GLIDES
for 2014 and earlier bikes see MX-TBARS Category
* 2018 and earlier STREET GLIDES

VERY IMPORTANT: IF YOU HAVE ABS. YOU WILL BE ABLE TO SWAP YOUR CURRENT CABLES AND WIRING TO THESE.
IF YOUR BIKE DO NOT HAVE ABS. YOU WILL NEED TO EXTEND YOUR CABLES AND WIRING OR GO DOWN A SIZE TO 12".

Coating: RAW

Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up 2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter. (Fits conventional controls)
- Both sides have 1/2" holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for the 3 1/2 spacing of the risers.
The throttle side tubing at 1" is honed out and notched for fly by wire.

Risers: 3 1/2" spacing between risers. (Fits conventional top triple tree clamps). 1/2" x 5/8" oval holes are 1 7/8" up from the bottom for internal wiring.

Recommendations:
- Heavy Duty Bushings FOR ROAD GLIDE
- Grade 8 or Grade 9 (L9) bolts
Keynote:
- These Handlebars are measured by overall height 12 inch risers with the 2 inch rise on the top cross bar equals 14 inches.
- 4 total weld points
- 2 holes will need to be made in the nacelle plastic to pass through and bolt down directly to the triple trees.
- On road glides the nipple on the underside of the vibration dampener on the inside part of the controls must be cut off to fit on our bars.

Here is RG15 Nacelle Cutout template link.CLICK HERE TO DOWNLOAD!

16 inch MX-TBARS RAW (RG15)

Features of your 16" Westcoast-Mxtbars RG15

Fitment:
* 2015-2020 ROAD GLIDES
for 2014 and earlier bikes see MX-TBARS Category
* 2018 and earlier STREET GLIDES

VERY IMPORTANT: Cable and wiring extensions will be needed for this size.

Coating: RAW

Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up 2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter. (Fits conventional controls)
- Both sides have 1/2" holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for the 3 1/2 spacing of the risers.
The throttle side tubing at 1" is honed out and notched for fly by wire.

Risers: 3 1/2" spacing between risers. (Fits conventional top triple tree clamps). 1/2" x 5/8" oval holes are 1 7/8" up from the bottom for internal wiring.

Recommendations:
- Heavy Duty Bushings FOR ROAD GLIDE
- Grade 8 bolts
Keynote:
- These Handlebars are measured by overall height 14 inch risers with the 2 inch rise on the top cross bar equals 16 inches.
- 4 total weld points
- 2 holes will need to be made in the nacelle plastic to pass through and bolt down directly to the triple trees.
- On road glides the nipple on the underside of the vibration dampener on the inside part of the controls must be cut off to fit on our bars.

Here is RG15 Nacelle Cutout template link.CLICK HERE TO DOWNLOAD!

10 inch MX-TBARS POWDERCOAT BLACK (RG15)

Features of your 10" Westcoast-Mxtbars RG15

Fitment:
* 2015-2020 ROAD GLIDES
for 2014 and earlier bikes see MX-TBARS Category
* 2018 and earlier STREET GLIDES

VERY IMPORTANT: ABS and NON ABS Road glides can use these bars with the current stock cables and wiring.

Coating: POWDERCOAT BLACK

Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up 2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter. (Fits conventional controls)
- Both sides have 1/2" holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for the 3 1/2 spacing of the risers.
The throttle side tubing at 1" is honed out and notched for fly by wire.

Risers: 3 1/2" spacing between risers. (Fits conventional top triple tree clamps). 1/2" x 5/8" oval holes are 1 7/8" up from the bottom for internal wiring.

Recommendations:
- Heavy Duty Bushings FOR ROAD GLIDE
- Grade 8 or Grade 9 (L9) bolts
Keynote:
- These Handlebars are measured by overall height 8 inch risers with the 2 inch rise on the top cross bar equals 10 inches.
- 4 total weld points

Here is RG15 Nacelle Cutout template link.CLICK HERE TO DOWNLOAD!

12 inch MX-TBARS POWDERCOAT BLACK (RG15)

Features of your 12" Westcoast-Mxtbars RG15

Fitment:
* 2015-2020 ROAD GLIDES
for 2014 and earlier bikes see MX-TBARS Category
* 2018 and earlier STREET GLIDES

VERY IMPORTANT: ABS and NON ABS Road glides can use these bars with the current stock cables and wiring.

Coating: POWDERCOAT BLACK

Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up 2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter. (Fits conventional controls)
- Both sides have 1/2" holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for the 3 1/2 spacing of the risers.
The throttle side tubing at 1" is honed out and notched for fly by wire.

Risers: 3 1/2" spacing between risers. (Fits conventional top triple tree clamps). 1/2" x 5/8" oval holes are 1 7/8" up from the bottom for internal wiring.

Recommendations:
- Heavy Duty Bushings FOR ROAD GLIDE
- Grade 8 or Grade 9 (L9) bolts
Keynote:
- These Handlebars are measured by overall height 10 inch risers with the 2 inch rise on the top cross bar equals 12 inches.
- 4 total weld points
- 2 holes will need to be made in the nacelle plastic to pass through and bolt down directly to the triple trees.
- On road glides the nipple on the underside of the vibration dampener on the inside part of the controls must be cut off to fit on our bars.

Here is RG15 Nacelle Cutout template link.CLICK HERE TO DOWNLOAD!

18 inch MX-TBARS POWDERCOAT BLACK (RG15)

Features of your 18" Westcoast-Mxtbars RG15

Fitment:
* 2015-2020 ROAD GLIDES
for 2014 and earlier bikes see MX-TBARS Category
* 2018 and earlier STREET GLIDES

VERY IMPORTANT: Cable and wiring extensions will be needed for this size.

Coating: POWDERCOAT BLACK

Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up 2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter. (Fits conventional controls)
- Both sides have 1/2" holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for the 3 1/2 spacing of the risers.
The throttle side tubing at 1" is honed out and notched for fly by wire.

Risers: 3 1/2" spacing between risers. (Fits conventional top triple tree clamps). 1/2" x 5/8" oval holes are 1 7/8" up from the bottom for internal wiring.

Recommendations:
- Heavy Duty Bushings FOR ROAD GLIDE
- Grade 8 bolts
Keynote:
- These Handlebars are measured by overall height 16 inch risers with the 2 inch rise on the top cross bar equals 18 inches.
- 4 total weld points
- 2 holes will need to be made in the nacelle plastic to pass through and bolt down directly to the triple trees.
- On road glides the nipple on the underside of the vibration dampener on the inside part of the controls must be cut off to fit on our bars.

Here is RG15 Nacelle Cutout template link.CLICK HERE TO DOWNLOAD!

14 inch MX-TBARS POWDERCOAT BLACK (RG15)

Features of your 14" Westcoast-Mxtbars RG15

Fitment:
* 2015-2020 ROAD GLIDES
for 2014 and earlier bikes see MX-TBARS Category
* 2018 and earlier STREET GLIDES

VERY IMPORTANT: IF YOU HAVE ABS. YOU WILL BE ABLE TO SWAP YOUR CURRENT CABLES AND WIRING TO THESE.
IF YOUR BIKE DO NOT HAVE ABS. YOU WILL NEED TO EXTEND YOUR CABLES AND WIRING OR GO DOWN A SIZE TO 12".

Coating: POWDERCOAT BLACK

Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up 2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter. (Fits conventional controls)
- Both sides have 1/2" holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for the 3 1/2 spacing of the risers.
The throttle side tubing at 1" is honed out and notched for fly by wire.

Risers: 3 1/2" spacing between risers. (Fits conventional top triple tree clamps). 1/2" x 5/8" oval holes are 1 7/8" up from the bottom for internal wiring.

Recommendations:
- Heavy Duty Bushings FOR ROAD GLIDE
- Grade 8 or Grade 9 (L9) bolts
Keynote:
- These Handlebars are measured by overall height 12 inch risers with the 2 inch rise on the top cross bar equals 14 inches.
- 4 total weld points
- 2 holes will need to be made in the nacelle plastic to pass through and bolt down directly to the triple trees.
- On road glides the nipple on the underside of the vibration dampener on the inside part of the controls must be cut off to fit on our bars.

Here is RG15 Nacelle Cutout template link.CLICK HERE TO DOWNLOAD!

16 inch MX-TBARS POWDERCOAT BLACK (RG15)

Features of your 16" Westcoast-Mxtbars RG15

Fitment:
* 2015-2020 ROAD GLIDES
for 2014 and earlier bikes see MX-TBARS Category
* 2018 and earlier STREET GLIDES

VERY IMPORTANT: Cable and wiring extensions will be needed for this size.

Coating: POWDERCOAT BLACK

Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up 2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter. (Fits conventional controls)
- Both sides have 1/2" holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for the 3 1/2 spacing of the risers.
The throttle side tubing at 1" is honed out and notched for fly by wire.

Risers: 3 1/2" spacing between risers. (Fits conventional top triple tree clamps). 1/2" x 5/8" oval holes are 1 7/8" up from the bottom for internal wiring.

Recommendations:
- Heavy Duty Bushings FOR ROAD GLIDE
- Grade 8 bolts
Keynote:
- These Handlebars are measured by overall height 14 inch risers with the 2 inch rise on the top cross bar equals 16 inches.
- 4 total weld points
- 2 holes will need to be made in the nacelle plastic to pass through and bolt down directly to the triple trees.
- On road glides the nipple on the underside of the vibration dampener on the inside part of the controls must be cut off to fit on our bars.

Here is RG15 Nacelle Cutout template link.CLICK HERE TO DOWNLOAD!