|
|
|
|
|
|
|
|
|
|
|
|
|
Features of your OG-Tbars 10" Risers
Coating: RAW
Top Crossbar:
- 1-1/4" swedged (tapered) down to 1"diameter 1080 mild gauge steel tubing. (Fits conventional controls)
- Dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 26" across and pullback is 0". (NOT THROTTLE BY WIRE COMPATIBLE)
Risers:
- Preciscion Laser cut
- 3 1/2" spacing between risers. (Fits conventional top triple tree clamps)
- 5/8" oval holes at the bottom for internal wiring.
Keynote:
- Risers are 10" tall and the top cross bar is welded on top of riser tubes.
- 4 weld points
|
WC212
|
Features of your OG-Tbars 14" Risers
Coating: CHROME
(Powdercoating ends 4 inches before each side for easier installation of your controls)
Top Crossbar:
- 1-1/4" swedged (tapered) down to 1"diameter 1080 mild gauge steel tubing. (Fits conventional controls)
- Dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 26" across and pullback is 0".
(NOT THROTTLE BY WIRE COMPATIBLE)
Risers:
- Preciscion Laser cut
- 3 1/2" spacing between risers. (Fits conventional top triple tree clamps)
- 5/8" oval holes at the bottom for internal wiring.
Keynote:
- Risers are 14" tall and the top cross bar is welded on top of riser tubes.
- 4 weld points
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Features of your OG-Tbars 16" Risers
Coating: RAW
Top Crossbar:
- 1-1/4" swaged (tapered) down to 1"diameter 1080 mild gauge steel tubing. (Fits conventional controls)
- Dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 26" across and pullback is 0".
(NOT THROTTLE BY WIRE COMPATIBLE)
Risers:
- Preciscion Laser cut
- 3 1/2" spacing between risers. (Fits conventional top triple tree clamps)
- 5/8" oval holes at the bottom for internal wiring.
Keynote:
- Risers are 16" tall and the top cross bar is welded on top of riser tubes.
- 4 weld points
|
Features of your OG-Tbars 10" Risers
Coating: POWDERCOAT BLACK
(Powdercoating ends 4 inches before each side for easier installation of your controls)
Top Crossbar:
- 1-1/4" swaged (tapered) down to 1"diameter 1080 mild gauge steel tubing. (Fits conventional controls)
- Dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 26" across and pullback is 0". (NOT THROTTLE BY WIRE COMPATIBLE)
Risers:
- Preciscion Laser cut
- 3 1/2" spacing between risers. (Fits conventional top triple tree clamps)
- 5/8" oval holes at the bottom for internal wiring.
Keynote:
- Risers are 10" tall and the top cross bar is welded on top of riser tubes.
- 4 weld points
|
Features of your OG-Tbars 12" Risers
Coating: POWDERCOAT BLACK
(Powdercoating ends 4 inches before each side for easier installation of your controls)
Top Crossbar:
- 1-1/4" swedged (tapered) down to 1"diameter 1080 mild gauge steel tubing. (Fits conventional controls)
- Dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 26" across and pullback is 0".
(NOT THROTTLE BY WIRE COMPATIBLE)
Risers:
- Preciscion Laser cut
- 3 1/2" spacing between risers. (Fits conventional top triple tree clamps)
- 5/8" oval holes at the bottom for internal wiring.
Keynote:
- Risers are 12" tall and the top cross bar is welded on top of riser tubes.
- 6 weld points
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Features of your OG-Tbars 14" Risers
Coating: Powdercoat Black (Powdercoating ends 4 inches before each side for easier installation of your controls)
Top Crossbar:
- 1-1/4" swaged (tapered) down to 1"diameter 1080 mild gauge steel tubing. (Fits conventional controls)
- Dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 26" across and pullback is 0".
(NOT THROTTLE BY WIRE COMPATIBLE)
Risers:
- Precision Laser cut
- 3 1/2" spacing between risers. (Fits conventional top triple tree clamps)
- 5/8" oval holes at the bottom for internal wiring.
Keynote:
- Risers are 14" tall and the top cross bar is welded on top of riser tubes.
- 4 weld points
|
Features of your OG-Tbars 16" Risers
Coating: POWDERCOAT BLACK
(Powdercoating ends 4 inches before each side for easier installation of your controls)
Top Crossbar:
- 1-1/4" swedged (tapered) down to 1"diameter 1080 mild gauge steel tubing. (Fits conventional controls)
- Dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 26" across and pullback is 0".
Risers:
- Preciscion Laser cut
- 3 1/2" spacing between risers. (Fits conventional top triple tree clamps)
- 5/8" oval holes at the bottom for internal wiring.
Keynote:
- Risers are 16" tall and the top cross bar is welded on top of riser tubes.
- 4 weld points
|
|
|
