|
|
|
|
|
|
|
|
|
|
|
|
|
Features of your MXTBARS 8" Risers SBOB
Metal: 1080 mild gauge steel tubing
Coating: Raw Metal
Color: N/A
Internal wiring: YES
Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up 2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter. (Fits conventional controls)
- Both sides are dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for the 3 1/2 spacing of the risers.
Risers: All cuts and holes are made by Laser cutting
- 3 1/2" spacing between risers.
- 1 1/4" at the top of the riser swaged (tapered) down to 1" diameter.
Original SBOB plate: 1/2" thick steel plate
- The risers are pressed through the the plate at a 14 degree angle and TIG welded at the top of the plate and the bottom of the plate.
Recommendations: Grade 8 or Grade 9 (L9) bolts
Keynotes: These Handlebars are measured by overall height 6 inch risers with the 2 inch rise on the top cross bar equals 8 inches.
- 6 total weld points YOUR STOCK SBOB CABLES AND WIRING WILL SWAP OVER WITHOUT HAVING TO
CHANGE ANY WIRING OR CABLES.
This SBOB model is specifically made for the 2008-2012 street bob HD
made with the Integrated Triple Trees. If you have a 2007 and earlier or
a 2013 and later then please go back and choose the standard Mxtbars.
|
Features of your MXTBARS 10" Risers SBOB
Metal: 1080 mild gauge steel tubing
Coating: Raw Metal
Color: N/A
Internal wiring: YES
Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up
2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter.
(Fits conventional controls)
- Both sides are dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to
sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for
the 3 1/2 spacing of the risers.
Risers: All cuts and holes are made by Laser cutting
- 3 1/2" spacing between risers.
- 1 1/4" at the top of the riser swaged (tapered) down to 1" diameter.
Original SBOB plate: 1/2" thick steel plate
- The risers are pressed through the the plate at a 14 degree angle and
TIG welded at the top of the plate and the bottom of the plate.
Keynotes: These Handlebars are measured by overall height 8 inch risers with the 2 inch rise on the top cross bar equals 10 inches.
- 6 total weld points YOUR STOCK SBOB CABLES AND WIRING WILL SWAP OVER WITHOUT HAVING TO
CHANGE ANY WIRING OR CABLES.
This SBOB model is specifically made for the 2008-2012 street bob HD
made with the Integrated Triple Trees. If you have a 2007 and earlier or
a 2013 and later then please go back and choose the standard Mxtbars.
|
Features of your MXTBARS 12" Risers SBOB
Metal: 1080 mild gauge steel tubing
Coating: Raw Metal
Color: N/A
Internal wiring: YES
Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up
2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter.
(Fits conventional controls)
- Both sides are dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to
sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for
the 3 1/2 spacing of the risers.
Risers: All cuts and holes are made by Laser cutting
- 3 1/2" spacing between risers.
- 1 1/4" at the top of the riser swaged (tapered) down to 1" diameter.
Original SBOB plate: 1/2" thick steel plate
- The risers are pressed through the the plate at a 14 degree angle and
TIG welded at the top of the plate and the bottom of the plate.
Keynotes: These Handlebars are measured by overall height 10 inch risers with the 2 inch rise on the top cross bar equals 12 inches.
- 6 total weld points YOUR STOCK SBOB CABLES AND WIRING WILL SWAP OVER WITHOUT HAVING TO
CHANGE ANY WIRING OR CABLES.
This SBOB model is specifically made for the 2008-2012 street bob HD
made with the Integrated Triple Trees. If you have a 2007 and earlier or
a 2013 and later then please go back and choose the standard Mxtbars.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Features of your MXTBARS 14" Risers SBOB
Metal: 1080 mild gauge steel tubing
Coating: Raw Metal
Color: N/A
Internal wiring: YES
Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up
2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter.
(Fits conventional controls)
- Both sides are dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to
sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for
the 3 1/2 spacing of the risers.
Risers: All cuts and holes are made by Laser cutting
- 3 1/2" spacing between risers.
- 1 1/4" at the top of the riser swaged (tapered) down to 1" diameter.
Original SBOB plate: 1/2" thick steel plate
- The risers are pressed through the the plate at a 14 degree angle and
TIG welded at the top of the plate and the bottom of the plate.
Keynotes: These Handlebars are measured by overall height 12 inch risers with the 2 inch rise on the top cross bar equals 14 inches.
- 6 total weld points
WE SUGGEST A +2 OVER STOCK CABLES FOR THIS BAR,
This SBOB model is specifically made for the 2008-2012 street bob HD
made with the Integrated Triple Trees. If you have a 2007 and earlier or
a 2013 and later then please go back and choose the standard Mxtbars.
|
Features of your MXTBARS 8" Risers SBOB
Metal: 1080 mild gauge steel tubing
Coating: POWDERCOAT
Color: BLACK
Internal wiring: YES
Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up
2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter.
(Fits conventional controls)
- Both sides are dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to
sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for
the 3 1/2 spacing of the risers.
Risers: All cuts and holes are made by Laser cutting
- 3 1/2" spacing between risers.
- 1 1/4" at the top of the riser swaged (tapered) down to 1" diameter.
Original SBOB plate: 1/2" thick steel plate
- The risers are pressed through the the plate at a 14 degree angle and
TIG welded at the top of the plate and the bottom of the plate.
Recommendations: Grade 8 or Grade 9 (L9) bolts
Keynotes: These Handlebars are measured by overall height 6 inch risers with the 2 inch rise on the top cross bar equals 8 inches.
- 6 total weld points YOUR STOCK SBOB CABLES AND WIRING WILL SWAP OVER WITHOUT HAVING TO
CHANGE ANY WIRING OR CABLES.
This SBOB model is specifically made for the 2008-2012 street bob HD
made with the Integrated Triple Trees. If you have a 2007 and earlier or
a 2013 and later then please go back and choose the standard Mxtbars.
|
Features of your MXTBARS 10" Risers SBOB
Metal: 1080 mild gauge steel tubing
Coating: POWDERCOAT
Color: BLACK
Internal wiring: YES
Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up
2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter.
(Fits conventional controls)
- Both sides are dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to
sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for
the 3 1/2 spacing of the risers.
Risers: All cuts and holes are made by Laser cutting
- 3 1/2" spacing between risers.
- 1 1/4" at the top of the riser swaged (tapered) down to 1" diameter.
Original SBOB plate: 1/2" thick steel plate
- The risers are pressed through the the plate at a 14 degree angle and
TIG welded at the top of the plate and the bottom of the plate.
Keynotes: These Handlebars are measured by overall height 8 inch risers with the 2 inch rise on the top cross bar equals 10 inches.
- 6 total weld points YOUR STOCK SBOB CABLES AND WIRING WILL SWAP OVER WITHOUT HAVING TO
CHANGE ANY WIRING OR CABLES.
This SBOB model is specifically made for the 2008-2012 street bob HD
made with the Integrated Triple Trees. If you have a 2007 and earlier or
a 2013 and later then please go back and choose the standard Mxtbars.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Features of your MXTBARS 12" Risers SBOB
Metal: 1080 mild gauge steel tubing
Coating: POWDERCOAT
Color: BLACK
Internal wiring: YES
Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up
2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter.
(Fits conventional controls)
- Both sides are dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to
sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for
the 3 1/2 spacing of the risers.
Risers: All cuts and holes are made by Laser cutting
- 3 1/2" spacing between risers.
- 1 1/4" at the top of the riser swaged (tapered) down to 1" diameter.
Original SBOB plate: 1/2" thick steel plate
- The risers are pressed through the the plate at a 14 degree angle and
TIG welded at the top of the plate and the bottom of the plate.
Keynotes: These Handlebars are measured by overall height 10 inch risers with the 2 inch rise on the top cross bar equals 12 inches.
- 6 total weld points YOUR STOCK SBOB CABLES AND WIRING WILL SWAP OVER WITHOUT HAVING TO
CHANGE ANY WIRING OR CABLES.
This SBOB model is specifically made for the 2008-2012 street bob HD
made with the Integrated Triple Trees. If you have a 2007 and earlier or
a 2013 and later then please go back and choose the standard Mxtbars.
|
Features of your MXTBARS 14" Risers SBOB
Metal: 1080 mild gauge steel tubing
Coating: POWDERCOAT
Color: BLACK
Internal wiring: YES
Top Crossbar:
- 5 1/2" spread in the middle of the handlebar. Then bends and rises up
2" and then the 1-1/4" tubing is swaged (tapered) down to 1"diameter.
(Fits conventional controls)
- Both sides are dimpled with 5/8" Holes punched for internal wiring.
- Cross width is 31 1/2" across and pullback is 3 1/2".
- Your Wrist angle will be at a 18 degree angle Cross bar is welded to
sit flat on a 28 degree rake
- The (2) - 3/4" holes in middle of the bar are made to be centered for
the 3 1/2 spacing of the risers.
Risers: All cuts and holes are made by Laser cutting
- 3 1/2" spacing between risers.
- 1 1/4" at the top of the riser swaged (tapered) down to 1" diameter.
Original SBOB plate: 1/2" thick steel plate
- The risers are pressed through the the plate at a 14 degree angle and
TIG welded at the top of the plate and the bottom of the plate.
Keynotes: These Handlebars are measured by overall height 12 inch risers with the 2 inch rise on the top cross bar equals 14 inches.
- 6 total weld points
WE SUGGEST A +2 OVER STOCK CABLES FOR THIS BAR,
This SBOB model is specifically made for the 2008-2012 street bob HD
made with the Integrated Triple Trees. If you have a 2007 and earlier or
a 2013 and later then please go back and choose the standard Mxtbars.
|
|
|
